Kyslík je plyn, ktorý sa v našich mysliach spája so životom. Primárnym zdrojom kyslíka sú rastliny. Vo vode je ho oveľa menej ako vo vzduchu. Koncentrácia kyslíka vo vode je závislá od teploty vody. Čím je teplota v akváriu vyššia, tým je koncentrácia O2 nižšia. Pri teplote 10 °C pri bežnom tlaku je vo vode rozpustených asi 11.3 mg O2 v litri, pri teplote 25 °C – 8.3 mg/l a pri 30 °C – 7.6 mg/l. Do vody sa kyslík okrem pôsobenia vodných rastlín dostáva aj difúziou zo vzduchu, premiešavaním, čerením hladiny. Kyslík sa spotrebúva v akváriu hlavne rozkladnou činnosťou mikroorganizmov – v substráte dna. Ak je dno málo prevzdušnené, môže dôjsť k jeho deficitu a tým k jeho vyčerpaniu pre ryby a rastliny. Kyslík napomáha rozkladu hmoty. Čistý, 100 % koncentrovaný kyslík je pre ľudský organizmus jedovatý, takže ak hovorím o kyslíku v súvislosti so vzduchovaním, ide samozrejme o vzduch. Vzduch obsahuje aj veľa dusíka a CO2. Rastlinám kyslík až tak veľmi “nevonia”, najmä nie cez deň a za dostatočného prísunu svetelnej energie. Aj ak spôsobuje vzduchovanie veľký pohyb vody, rastlinám to neprospieva. Naopak cez noc, kedy rastliny kyslík prijímajú by bol pre ne kyslík vítaný. Cez deň rastliny prijímajú oxid uhličitý – ide o proces fotosyntézy a z nej vyplývajúcich procesov ako napr. Krebsov cyklus, cyklus C, N, apod. Vzduchovanie homogenizuje vodu v akváriu, zabezpečuje pohyb vody, miešanie jednotlivých vrstiev, najmä vertikálnym smerom. Množstvo kyslíka, ktoré dokáže vzduchovanie odovzdať akváriu je pomerne nízke – difúzia plynov vo vode je rádovo štyri krát nižšia ako vo vzduchu. Darmo budeme vytvárať veľké bublinky, tie síce viac rozprúdia vodu, ale množstvo prijatého kyslíka vodou bude nižšie ako keby sme produkovali menšie bublinky. Množstvo takto prijatého kyslíka závisí na povrchu bubliniek, ktorý je vyšší pri menších bublinkách.
Vzduchovací kameň môže mať rôzny tvar. Môže to byť valec, gulička, môže byť podlhovastý, až 105 cm dlhý. Existujú kamene tvaru obvodu kruhu. Podobne ako vzduchovací kameň je možné použiť lipové drievko, ktoré tvorí malé bublinky. Jeho nevýhoda je vtom, že sa póry v ňom rýchlo uzavrú. Používa sa skôr pri difúzii CO2 – pri hnojení rastlín. Navyše sa lipové drievko rozkladá a obrastá riasami. Určite neopomenuteľným spôsobom transportu kyslíka do vody je čerenie hladiny, ktoré spôsobuje buď vzduchovanie cez kameň, alebo filter. Väčšina návodov na používanie filtra odporúča umiestniť filter tak, aby vývod vody bol na hladinou alebo tesne pod ňou. Aj takto sa dostáva kyslík do vody. Na vzduchovanie sa v akvaristike používajú dmychadlá, z ktorých je vzduch poháňaný vzduch do hadičiek buď do vzduchovacích kameňov, alebo do filtrov. Ja používam niekoľko typov motorčekov o rôznej sile. Dmychadlo by malo byť umiestnené nad všetkými hladinami, do ktorých vháňa vzduch, aby sa predišlo pri výpadku prúdu samospádovému vniknutiu vody do kompresora. V prípade, že nie je možné kompresor takto umiestniť, hadičku na jej ceste od kompresora ku akváriám najprv vedieme meter nad úroveň najvyššej hladiny, alebo zabezpečíme iné technické riešenie, ktoré zabráni nasávaniu vody, napr. použijem spätný ventil. Ak sa niekedy stretnete s pojmom korytnačka, tak vedzte že možno pôjde o väčšie dmychadlo, ktoré je pre väčší priemer trubky, resp. hadice (napr. záhradnej). Často sa používa tam, kde je viacej nádrží. Druhá možnosť je vzduchovať cez filter. Niektoré filtre dokážu otvorom vo vrchnej časti filtra nasávať cez pripojenú hadičku vzduch. Ja to využívam, a považujem tento spôsob sa lepší, funkčnejší. Hadička sa dá priškrtiť podľa potreby, aby poskytovala vzduch ako vám vyhovuje. Takto prispôsobené vzduchovanie má lepší efekt, pretože bublinky sú vháňané do vody vodorovne a sú menšie ak to potrebujeme. Zrejme aj tým, že majú istú zotrvačnosť a malý objem, ich presun na hladinu a teda vyparenie trvá oveľa dlhšie než pri vzduchovaní kameňom. Difúzia plynov do vody je účinnejšia, pretože trvá dlhšie a prebieha na väčšom povrchu.
Oxygen is a gas that we associate with life in our minds. Plants are the primary source of oxygen. There is much less oxygen in water than in the air. The concentration of oxygen in water depends on the water temperature. The higher the temperature in the aquarium, the lower the concentration of O2. At a temperature of 10 °C at normal pressure, there are about 11.3 mg of O2 dissolved in a liter of water, at a temperature of 25 °C – 8.3 mg/l, and at 30 °C – 7.6 mg/l. Oxygen enters the water not only through the action of aquatic plants but also through diffusion from the air, mixing, and surface agitation. Oxygen is mainly consumed in the aquarium by the decomposition activity of microorganisms in the substrate. If the substrate is poorly aerated, this can lead to a deficiency and depletion of oxygen for fish and plants. Oxygen promotes the breakdown of matter. Pure, 100% concentrated oxygen is toxic to the human body, so when I talk about oxygen in the context of aeration, I’m referring, of course, to air. Air also contains a lot of nitrogen and CO2. Plants don’t “like” oxygen all that much, especially not during the day and with sufficient supply of light energy. Even though aeration causes significant water movement, it is not beneficial for plants. On the contrary, oxygen would be welcome for them during the night when plants absorb oxygen. During the day, plants absorb carbon dioxide – this is the process of photosynthesis and the resulting processes such as the Krebs cycle, the C cycle, N cycle, etc. Aeration homogenizes the water in the aquarium, provides water movement, and mixes individual layers, especially vertically. The amount of oxygen that aeration can deliver to the aquarium is relatively low – the diffusion of gases in water is orders of magnitude lower than in air. It is pointless to create large bubbles; although they may agitate the water more, the amount of oxygen absorbed by the water will be lower than if we produced smaller bubbles. The amount of oxygen absorbed in this way depends on the surface area of the bubbles, which is higher with smaller bubbles.
An airstone can have various shapes. It can be cylindrical, spherical, or elongated, up to 105 cm long. There are stones shaped like the circumference of a circle. Similarly to an airstone, a wood diffuser can be used, which creates small bubbles. Its disadvantage is that the pores in it close quickly. It is used more for CO2 diffusion – for plant fertilization. Moreover, the wood diffuser decomposes and becomes covered with algae. Another essential way to transport oxygen into the water is surface agitation, which either aerates through the stone or filter. Most filter usage instructions recommend placing the filter so that the water outlet is at or just below the surface. This way, oxygen gets into the water. In aquaristics, air pumps are used for aeration, from which air is driven through tubes either to airstones or filters. I use several types of air pumps of varying power. The air pump should be positioned above all water levels into which it delivers air to prevent water from entering the compressor in the event of a power outage. If it is not possible to place the compressor in this way, the tube on its way from the compressor to the aquarium is first led one meter above the highest water level, or another technical solution is provided to prevent water from entering, for example, I use a check valve. If you ever come across the term “turtle,” it might refer to a larger air pump designed for a larger pipe or hose (e.g., garden). It is often used where there are multiple tanks. Another option is to aerate through the filter. Some filters can draw air through a connected tube into the upper part of the filter. I use this method and consider it better and more functional. The tube can be adjusted as needed to provide air as you like. This adapted aeration has a better effect because the bubbles are introduced into the water horizontally and are smaller if needed. Probably also because they have a certain inertia and a small volume, their movement to the surface and therefore evaporation takes much longer than with stone aeration. Gas diffusion into the water is more effective because it takes longer and occurs over a larger surface area.
Sauerstoff ist ein Gas, das wir in unseren Köpfen mit Leben verbinden. Pflanzen sind die primäre Quelle für Sauerstoff. Im Wasser gibt es viel weniger Sauerstoff als in der Luft. Die Konzentration von Sauerstoff im Wasser hängt von der Wassertemperatur ab. Je höher die Temperatur im Aquarium ist, desto geringer ist die Konzentration von O2. Bei einer Temperatur von 10 °C bei normalem Druck gibt es etwa 11,3 mg O2 pro Liter Wasser, bei einer Temperatur von 25 °C – 8,3 mg/l und bei 30 °C – 7,6 mg/l. Sauerstoff gelangt nicht nur durch die Wirkung von Wasserpflanzen ins Wasser, sondern auch durch Diffusion aus der Luft, durch Vermischung und Oberflächenbewegung. Sauerstoff wird im Aquarium hauptsächlich durch die Zersetzungsaktivität von Mikroorganismen im Substrat verbraucht. Ist das Substrat schlecht belüftet, kann dies zu einem Mangel und einer Erschöpfung von Sauerstoff für Fische und Pflanzen führen. Sauerstoff fördert den Abbau von Materie. Reiner, 100% konzentrierter Sauerstoff ist für den menschlichen Körper giftig, daher meine ich, wenn ich über Sauerstoff im Zusammenhang mit Belüftung spreche, natürlich Luft. Luft enthält auch viel Stickstoff und CO2. Pflanzen “mögen” Sauerstoff nicht so sehr, besonders nicht tagsüber und bei ausreichender Lichtenergie. Auch wenn die Belüftung zu einer erheblichen Wasserbewegung führt, ist dies nicht förderlich für Pflanzen. Im Gegenteil, Sauerstoff wäre für sie während der Nacht, in der Pflanzen Sauerstoff aufnehmen, willkommen. Tagsüber nehmen Pflanzen Kohlendioxid auf – dies ist der Prozess der Photosynthese und der daraus resultierenden Prozesse wie dem Citratzyklus, dem C‑Zyklus, dem N‑Zyklus usw. Belüftung homogenisiert das Wasser im Aquarium, sorgt für Wasserbewegung und mischt einzelne Schichten, insbesondere vertikal. Die Menge an Sauerstoff, die Belüftung dem Aquarium zuführen kann, ist relativ gering – die Diffusion von Gasen im Wasser ist um Größenordnungen geringer als in der Luft. Es ist sinnlos, große Blasen zu erzeugen; obwohl sie das Wasser mehr bewegen können, ist die Menge an Sauerstoff, die das Wasser aufnimmt, geringer als bei kleineren Blasen. Die Menge an auf diese Weise aufgenommenem Sauerstoff hängt von der Oberfläche der Blasen ab, die bei kleineren Blasen höher ist.
Ein Luftstein kann verschiedene Formen haben. Er kann zylindrisch, kugelförmig oder länglich bis zu 105 cm lang sein. Es gibt Steine in Form des Umfangs eines Kreises. Ähnlich wie ein Luftstein kann ein Holzdiffusor verwendet werden, der kleine Blasen erzeugt. Sein Nachteil ist, dass sich die Poren darin schnell schließen. Es wird eher für die CO2-Diffusion – zur Pflanzendüngung verwendet. Außerdem zersetzt sich der Holzdiffusor und wird von Algen überzogen. Eine weitere wichtige Möglichkeit, Sauerstoff ins Wasser zu transportieren, ist die Oberflächenbewegung, die entweder durch den Stein oder den Filter belüftet. Die meisten Anweisungen zur Filterverwendung empfehlen, den Filter so zu platzieren, dass der Wasserablauf auf oder knapp unter der Oberfläche liegt. So gelangt Sauerstoff ins Wasser. In der Aquaristik werden Luftkompressoren zur Belüftung verwendet, aus denen Luft durch Schläuche entweder zu Luftsteinen oder Filtern geleitet wird. Ich verwende mehrere Arten von Luftkompressoren unterschiedlicher Leistung. Der Luftkompressor sollte über allen Wasserständen platziert werden, in die er Luft abgibt, um zu verhindern, dass Wasser bei einem Stromausfall in den Kompressor gelangt. Ist es nicht möglich, den Kompressor auf diese Weise zu platzieren, wird das Rohr auf seinem Weg vom Kompressor zum Aquarium zunächst einen Meter über dem höchsten Wasserstand geführt, oder es wird eine andere technische Lösung bereitgestellt, um das Eindringen von Wasser zu verhindern, zum Beispiel verwende ich ein Rückschlagventil. Wenn Sie jemals auf den Begriff “Schildkröte” stoßen, könnte dies sich auf eine größere Luftpumpe für ein größeres Rohr oder einen Schlauch (z.B. Garten) beziehen. Es wird oft dort verwendet, wo es mehrere Tanks gibt. Eine andere Möglichkeit ist die Belüftung durch den Filter. Einige Filter können Luft durch einen angeschlossenen Schlauch in den oberen Teil des Filters ziehen. Ich verwende diese Methode und halte sie für besser und funktionaler. Der Schlauch kann je nach Bedarf angepasst werden, um Luft zu liefern, wie es Ihnen gefällt. Diese angepasste Belüftung hat eine bessere Wirkung, weil die Blasen horizontal in das Wasser eingeführt werden und kleiner sind, wenn nötig. Wahrscheinlich auch, weil sie eine gewisse Trägheit und ein kleines Volumen haben, dauert ihre Bewegung zur Oberfläche und damit die Verdunstung viel länger als bei Steinbelüftung. Die Gasdiffusion ins Wasser ist effektiver, weil sie länger dauert und über eine größere Oberfläche stattfindet.
Use Facebook to Comment on this Post
- Vodné rastliny (41.8%)
- Filtrácia (27.1%)
- Kyslík v živote rýb – pozitíva i negatíva (24.6%)
- Údržba akvária (22%)
- Teplota vody (21.4%)
- Osvetlenie akvária (16%)
- Nádrž (15.6%)
- Fyziológia rýb a rastlín (12.7%)
- Úprava vody (12.4%)
- Založenie akvária (11%)