Hits: 35471

Kys­lík je plyn, kto­rý sa v našich mys­liach spá­ja so živo­tom. Pri­már­nym zdro­jom kys­lí­ka sú rast­li­ny. Vo vode je ho ove­ľa menej ako vo vzdu­chu. Kon­cen­trá­cia kys­lí­ka vo vode je závis­lá od tep­lo­ty vody. Čím je tep­lo­ta v akvá­riu vyš­šia, tým je kon­cen­trá­cia O2 niž­šia. Pri tep­lo­te 10°C pri bež­nom tla­ku je vo vode roz­pus­te­ných asi 11.3 mg O2 v lit­ri, pri tep­lo­te 25°C – 8.3 mg/​l a pri 30°C – 7.6 mg/​l. Do vody sa kys­lík okrem pôso­be­nia vod­ných rast­lín dostá­va aj difú­zi­ou zo vzdu­chu, pre­mie­ša­va­ním, čere­ním hla­di­ny. Kys­lík sa spot­re­bú­va v akvá­riu hlav­ne roz­klad­nou čin­nos­ťou mik­ro­or­ga­niz­mov – v sub­strá­te dna. Ak je dno málo pre­vzduš­ne­né, môže dôjsť k jeho defi­ci­tu a tým k jeho vyčer­pa­niu pre ryby a rast­li­ny. Kys­lík napo­má­ha roz­kla­du hmo­ty. Čis­tý, 100 % kon­cen­tro­va­ný kys­lík je pre ľud­ský orga­niz­mus jedo­va­tý, tak­že ak hovo­rím o kys­lí­ku v súvis­los­ti so vzdu­cho­va­ním, ide samoz­rej­me o vzduch. Vzduch obsa­hu­je aj veľa dusí­kaCO2. Rast­li­nám kys­lík až tak veľ­mi nevo­nia”, naj­mä nie cez deň a za dosta­toč­né­ho prí­su­nu sve­tel­nej ener­gie. Aj ak spô­so­bu­je vzdu­cho­va­nie veľ­ký pohyb vody, rast­li­nám to nepro­spie­va. Naopak cez noc, kedy rast­li­ny kys­lík pri­jí­ma­jú by bol pre ne kys­lík víta­ný. Cez deň rast­li­ny pri­jí­ma­jú oxid uhli­či­tý – ide o pro­ces foto­syn­té­zy a z nej vyplý­va­jú­cich pro­ce­sov ako napr. Kreb­sov cyk­lus, cyk­lus C, N, apod. Vzdu­cho­va­nie homo­ge­ni­zu­je vodu v akvá­riu, zabez­pe­ču­je pohyb vody, mie­ša­nie jed­not­li­vých vrs­tiev, naj­mä ver­ti­kál­nym sme­rom. Množ­stvo kys­lí­ka, kto­ré doká­že vzdu­cho­va­nie odo­vzdať akvá­riu je pomer­ne níz­ke – difú­zia ply­nov vo vode je rádo­vo šty­ri krát niž­šia ako vo vzdu­chu. Dar­mo bude­me vytvá­rať veľ­ké bub­lin­ky, tie síce viac rozp­rú­dia vodu, ale množ­stvo pri­ja­té­ho kys­lí­ka vodou bude niž­šie ako keby sme pro­du­ko­va­li men­šie bub­lin­ky. Množ­stvo tak­to pri­ja­té­ho kys­lí­ka závi­sí na povr­chu bub­li­niek, kto­rý je vyš­ší pri men­ších bublinkách.

Vzdu­cho­va­cí kameň môže mať rôz­ny tvar. Môže to byť valec, gulič­ka, môže byť podl­ho­vas­tý, až 105 cm dlhý. Exis­tu­jú kame­ne tva­ru obvo­du kru­hu. Podob­ne ako vzdu­cho­va­cí kameň je mož­né pou­žiť lipo­vé driev­ko, kto­ré tvo­rí malé bub­lin­ky. Jeho nevý­ho­da je vtom, že sa póry v ňom rých­lo uzav­rú. Pou­ží­va sa skôr pri difú­zii CO2 – pri hno­je­ní rast­lín. Navy­še sa lipo­vé driev­ko roz­kla­dá a obras­tá ria­sa­mi. Urči­te neopo­me­nu­teľ­ným spô­so­bom tran­s­por­tu kys­lí­ka do vody je čere­nie hla­di­ny, kto­ré spô­so­bu­je buď vzdu­cho­va­nie cez kameň, ale­bo fil­ter. Väč­ši­na návo­dov na pou­ží­va­nie fil­tra odpo­rú­ča umiest­niť fil­ter tak, aby vývod vody bol na hla­di­nou ale­bo tes­ne pod ňou. Aj tak­to sa dostá­va kys­lík do vody. Na vzdu­cho­va­nie sa v akva­ris­ti­ke pou­ží­va­jú dmy­chad­lá, z kto­rých je vzduch pohá­ňa­ný vzduch do hadi­čiek buď do vzdu­cho­va­cích kame­ňov, ale­bo do fil­trov. Ja pou­ží­vam nie­koľ­ko typov motor­če­kov o rôz­nej sile. Dmy­chad­lo by malo byť umiest­ne­né nad všet­ký­mi hla­di­na­mi, do kto­rých vhá­ňa vzduch, aby sa pre­d­iš­lo pri výpad­ku prú­du samos­pá­do­vé­mu vnik­nu­tiu vody do kom­pre­so­ra. V prí­pa­de, že nie je mož­né kom­pre­sor tak­to umiest­niť, hadič­ku na jej ces­te od kom­pre­so­ra ku akvá­riám najprv vedie­me meter nad úro­veň naj­vyš­šej hla­di­ny, ale­bo zabez­pe­čí­me iné tech­nic­ké rie­še­nie, kto­ré zabrá­ni nasá­va­niu vody, napr. pou­ži­jem spät­ný ven­til. Ak sa nie­ke­dy stret­ne­te s poj­mom koryt­nač­ka, tak vedz­te že mož­no pôj­de o väč­šie dmy­chad­lo, kto­ré je pre väč­ší prie­mer trub­ky, resp. hadi­ce (napr. záh­rad­nej). Čas­to sa pou­ží­va tam, kde je via­cej nádr­ží. Dru­há mož­nosť je vzdu­cho­vať cez fil­ter. Nie­kto­ré fil­tre doká­žu otvo­rom vo vrch­nej čas­ti fil­tra nasá­vať cez pri­po­je­nú hadič­ku vzduch. Ja to využí­vam, a pova­žu­jem ten­to spô­sob sa lep­ší, funkč­nej­ší. Hadič­ka sa dá pri­škr­tiť pod­ľa potre­by, aby posky­to­va­la vzduch ako vám vyho­vu­je. Tak­to pris­pô­so­be­né vzdu­cho­va­nie má lep­ší efekt, pre­to­že bub­lin­ky sú vhá­ňa­né do vody vodo­rov­ne a sú men­šie ak to potre­bu­je­me. Zrej­me aj tým, že majú istú zotr­vač­nosť a malý objem, ich pre­sun na hla­di­nu a teda vypa­re­nie trvá ove­ľa dlh­šie než pri vzdu­cho­va­ní kame­ňom. Difú­zia ply­nov do vody je účin­nej­šia, pre­to­že trvá dlh­šie a pre­bie­ha na väč­šom povrchu.


Oxy­gen is a gas that we asso­cia­te with life in our minds. Plants are the pri­ma­ry sour­ce of oxy­gen. The­re is much less oxy­gen in water than in the air. The con­cen­tra­ti­on of oxy­gen in water depends on the water tem­pe­ra­tu­re. The hig­her the tem­pe­ra­tu­re in the aqu­arium, the lower the con­cen­tra­ti­on of O2. At a tem­pe­ra­tu­re of 10°C at nor­mal pre­ssu­re, the­re are about 11.3 mg of O2 dis­sol­ved in a liter of water, at a tem­pe­ra­tu­re of 25°C – 8.3 mg/​l, and at 30°C – 7.6 mg/​l. Oxy­gen enters the water not only through the acti­on of aqu­atic plants but also through dif­fu­si­on from the air, mixing, and sur­fa­ce agi­ta­ti­on. Oxy­gen is main­ly con­su­med in the aqu­arium by the decom­po­si­ti­on acti­vi­ty of mic­ro­or­ga­nisms in the sub­stra­te. If the sub­stra­te is poor­ly aera­ted, this can lead to a defi­cien­cy and dep­le­ti­on of oxy­gen for fish and plants. Oxy­gen pro­mo­tes the bre­ak­do­wn of mat­ter. Pure, 100% con­cen­tra­ted oxy­gen is toxic to the human body, so when I talk about oxy­gen in the con­text of aera­ti­on, I’m refer­ring, of cour­se, to air. Air also con­tains a lot of nit­ro­gen and CO2. Plants don’t like” oxy­gen all that much, espe­cial­ly not during the day and with suf­fi­cient supp­ly of light ener­gy. Even though aera­ti­on cau­ses sig­ni­fi­cant water move­ment, it is not bene­fi­cial for plants. On the con­tra­ry, oxy­gen would be wel­co­me for them during the night when plants absorb oxy­gen. During the day, plants absorb car­bon dioxi­de – this is the pro­cess of pho­to­synt­he­sis and the resul­ting pro­ces­ses such as the Krebs cyc­le, the C cyc­le, N cyc­le, etc. Aera­ti­on homo­ge­ni­zes the water in the aqu­arium, pro­vi­des water move­ment, and mixes indi­vi­du­al lay­ers, espe­cial­ly ver­ti­cal­ly. The amount of oxy­gen that aera­ti­on can deli­ver to the aqu­arium is rela­ti­ve­ly low – the dif­fu­si­on of gases in water is orders of mag­ni­tu­de lower than in air. It is poin­tless to cre­a­te lar­ge bubb­les; alt­hough they may agi­ta­te the water more, the amount of oxy­gen absor­bed by the water will be lower than if we pro­du­ced smal­ler bubb­les. The amount of oxy­gen absor­bed in this way depends on the sur­fa­ce area of the bubb­les, which is hig­her with smal­ler bubbles.

An airs­to­ne can have vari­ous sha­pes. It can be cylin­dri­cal, sphe­ri­cal, or elon­ga­ted, up to 105 cm long. The­re are sto­nes sha­ped like the cir­cum­fe­ren­ce of a circ­le. Simi­lar­ly to an airs­to­ne, a wood dif­fu­ser can be used, which cre­a­tes small bubb­les. Its disad­van­ta­ge is that the pores in it clo­se quick­ly. It is used more for CO2 dif­fu­si­on – for plant fer­ti­li­za­ti­on. More­over, the wood dif­fu­ser decom­po­ses and beco­mes cove­red with algae. Anot­her essen­tial way to tran­s­port oxy­gen into the water is sur­fa­ce agi­ta­ti­on, which eit­her aera­tes through the sto­ne or fil­ter. Most fil­ter usa­ge ins­truc­ti­ons recom­mend pla­cing the fil­ter so that the water out­let is at or just below the sur­fa­ce. This way, oxy­gen gets into the water. In aqu­aris­tics, air pumps are used for aera­ti­on, from which air is dri­ven through tubes eit­her to airs­to­nes or fil­ters. I use seve­ral types of air pumps of vary­ing power. The air pump should be posi­ti­oned abo­ve all water levels into which it deli­vers air to pre­vent water from ente­ring the com­pres­sor in the event of a power outa­ge. If it is not possib­le to pla­ce the com­pres­sor in this way, the tube on its way from the com­pres­sor to the aqu­arium is first led one meter abo­ve the hig­hest water level, or anot­her tech­ni­cal solu­ti­on is pro­vi­ded to pre­vent water from ente­ring, for exam­ple, I use a check val­ve. If you ever come across the term turt­le,” it might refer to a lar­ger air pump desig­ned for a lar­ger pipe or hose (e.g., gar­den). It is often used whe­re the­re are mul­tip­le tanks. Anot­her opti­on is to aera­te through the fil­ter. Some fil­ters can draw air through a con­nec­ted tube into the upper part of the fil­ter. I use this met­hod and con­si­der it bet­ter and more func­ti­onal. The tube can be adjus­ted as needed to pro­vi­de air as you like. This adap­ted aera­ti­on has a bet­ter effect becau­se the bubb­les are intro­du­ced into the water hori­zon­tal­ly and are smal­ler if needed. Pro­bab­ly also becau­se they have a cer­tain iner­tia and a small volu­me, the­ir move­ment to the sur­fa­ce and the­re­fo­re eva­po­ra­ti­on takes much lon­ger than with sto­ne aera­ti­on. Gas dif­fu­si­on into the water is more effec­ti­ve becau­se it takes lon­ger and occurs over a lar­ger sur­fa­ce area.


Sau­ers­toff ist ein Gas, das wir in unse­ren Köp­fen mit Leben ver­bin­den. Pflan­zen sind die pri­mä­re Quel­le für Sau­ers­toff. Im Was­ser gibt es viel weni­ger Sau­ers­toff als in der Luft. Die Kon­zen­tra­ti­on von Sau­ers­toff im Was­ser hängt von der Was­ser­tem­pe­ra­tur ab. Je höher die Tem­pe­ra­tur im Aqu­arium ist, des­to gerin­ger ist die Kon­zen­tra­ti­on von O2. Bei einer Tem­pe­ra­tur von 10°C bei nor­ma­lem Druck gibt es etwa 11,3 mg O2 pro Liter Was­ser, bei einer Tem­pe­ra­tur von 25°C – 8,3 mg/​l und bei 30°C – 7,6 mg/​l. Sau­ers­toff gelangt nicht nur durch die Wir­kung von Was­serpf­lan­zen ins Was­ser, son­dern auch durch Dif­fu­si­on aus der Luft, durch Ver­mis­chung und Oberf­lä­chen­be­we­gung. Sau­ers­toff wird im Aqu­arium haupt­säch­lich durch die Zer­set­zung­sak­ti­vi­tät von Mik­ro­or­ga­nis­men im Sub­strat verb­raucht. Ist das Sub­strat sch­lecht belüf­tet, kann dies zu einem Man­gel und einer Ers­chöp­fung von Sau­ers­toff für Fis­che und Pflan­zen füh­ren. Sau­ers­toff för­dert den Abbau von Mate­rie. Rei­ner, 100% kon­zen­trier­ter Sau­ers­toff ist für den men­sch­li­chen Kör­per gif­tig, daher mei­ne ich, wenn ich über Sau­ers­toff im Zusam­men­hang mit Belüf­tung spre­che, natür­lich Luft. Luft ent­hält auch viel Sticks­toff und CO2. Pflan­zen mögen” Sau­ers­toff nicht so sehr, beson­ders nicht tag­süber und bei aus­re­i­chen­der Lich­te­ner­gie. Auch wenn die Belüf­tung zu einer erheb­li­chen Was­ser­be­we­gung führt, ist dies nicht för­der­lich für Pflan­zen. Im Gegen­te­il, Sau­ers­toff wäre für sie wäh­rend der Nacht, in der Pflan­zen Sau­ers­toff auf­neh­men, will­kom­men. Tag­süber neh­men Pflan­zen Koh­len­di­oxid auf – dies ist der Pro­zess der Pho­to­synt­he­se und der daraus resul­tie­ren­den Pro­zes­se wie dem Cit­rat­zyk­lus, dem C‑Zyklus, dem N‑Zyklus usw. Belüf­tung homo­ge­ni­siert das Was­ser im Aqu­arium, sorgt für Was­ser­be­we­gung und mischt ein­zel­ne Schich­ten, ins­be­son­de­re ver­ti­kal. Die Men­ge an Sau­ers­toff, die Belüf­tung dem Aqu­arium zufüh­ren kann, ist rela­tiv gering – die Dif­fu­si­on von Gasen im Was­ser ist um Größe­nord­nun­gen gerin­ger als in der Luft. Es ist sinn­los, gro­ße Bla­sen zu erze­ugen; obwohl sie das Was­ser mehr bewe­gen kön­nen, ist die Men­ge an Sau­ers­toff, die das Was­ser auf­nimmt, gerin­ger als bei kle­i­ne­ren Bla­sen. Die Men­ge an auf die­se Wei­se auf­ge­nom­me­nem Sau­ers­toff hängt von der Oberf­lä­che der Bla­sen ab, die bei kle­i­ne­ren Bla­sen höher ist.

Ein Lufts­te­in kann vers­chie­de­ne For­men haben. Er kann zylin­drisch, kugel­för­mig oder län­glich bis zu 105 cm lang sein. Es gibt Ste­i­ne in Form des Umfangs eines Kre­i­ses. Ähn­lich wie ein Lufts­te­in kann ein Holz­dif­fu­sor ver­wen­det wer­den, der kle­i­ne Bla­sen erze­ugt. Sein Nach­te­il ist, dass sich die Poren darin schnell sch­lie­ßen. Es wird eher für die CO2-​Diffusion – zur Pflan­zen­dün­gung ver­wen­det. Außer­dem zer­setzt sich der Holz­dif­fu­sor und wird von Algen über­zo­gen. Eine wei­te­re wich­ti­ge Mög­lich­ke­it, Sau­ers­toff ins Was­ser zu tran­s­por­tie­ren, ist die Oberf­lä­chen­be­we­gung, die ent­we­der durch den Ste­in oder den Fil­ter belüf­tet. Die meis­ten Anwe­i­sun­gen zur Fil­ter­ver­wen­dung emp­feh­len, den Fil­ter so zu plat­zie­ren, dass der Was­se­rab­lauf auf oder knapp unter der Oberf­lä­che liegt. So gelangt Sau­ers­toff ins Was­ser. In der Aqu­aris­tik wer­den Luft­kom­pres­so­ren zur Belüf­tung ver­wen­det, aus denen Luft durch Sch­lä­u­che ent­we­der zu Lufts­te­i­nen oder Fil­tern gele­i­tet wird. Ich ver­wen­de meh­re­re Arten von Luft­kom­pres­so­ren unters­chied­li­cher Leis­tung. Der Luft­kom­pres­sor soll­te über allen Was­sers­tän­den plat­ziert wer­den, in die er Luft abgibt, um zu ver­hin­dern, dass Was­ser bei einem Stro­maus­fall in den Kom­pres­sor gelangt. Ist es nicht mög­lich, den Kom­pres­sor auf die­se Wei­se zu plat­zie­ren, wird das Rohr auf sei­nem Weg vom Kom­pres­sor zum Aqu­arium zunächst einen Meter über dem höchs­ten Was­sers­tand gefü­hrt, oder es wird eine ande­re tech­nis­che Lösung bere­it­ges­tellt, um das Ein­drin­gen von Was­ser zu ver­hin­dern, zum Beis­piel ver­wen­de ich ein Rücksch­lag­ven­til. Wenn Sie jemals auf den Beg­riff Schildk­röte” sto­ßen, könn­te dies sich auf eine größe­re Luft­pum­pe für ein größe­res Rohr oder einen Sch­lauch (z.B. Gar­ten) bez­ie­hen. Es wird oft dort ver­wen­det, wo es meh­re­re Tanks gibt. Eine ande­re Mög­lich­ke­it ist die Belüf­tung durch den Fil­ter. Eini­ge Fil­ter kön­nen Luft durch einen angesch­los­se­nen Sch­lauch in den obe­ren Teil des Fil­ters zie­hen. Ich ver­wen­de die­se Met­ho­de und hal­te sie für bes­ser und funk­ti­ona­ler. Der Sch­lauch kann je nach Bedarf ange­passt wer­den, um Luft zu lie­fern, wie es Ihnen gefällt. Die­se ange­pass­te Belüf­tung hat eine bes­se­re Wir­kung, weil die Bla­sen hori­zon­tal in das Was­ser ein­ge­fü­hrt wer­den und kle­i­ner sind, wenn nötig. Wahrs­che­in­lich auch, weil sie eine gewis­se Träg­he­it und ein kle­i­nes Volu­men haben, dau­ert ihre Bewe­gung zur Oberf­lä­che und damit die Ver­duns­tung viel län­ger als bei Ste­in­be­lüf­tung. Die Gas­dif­fu­si­on ins Was­ser ist effek­ti­ver, weil sie län­ger dau­ert und über eine größe­re Oberf­lä­che stattfindet.

Use Facebook to Comment on this Post